66´´ X 40,000 LB. STAMCO SLITTING LINE (USED)
Inventory #: VX-1269

Specifications

General Specifications:
Manufacturer: Monarch Stamco
Year Manufactured: 1985
Coil Width:
1) Entry: 30" to 66"
2) Exity: .75" to 66" Slit
Gauge:
1) Minimum: .005"
2) Maximum: .020"
Coil O.D.:
1) Entry: 40" to 96"
2) Exit: 20" to 96"
Coil Weight Maximum: 40,000 Lbs.
Coil Slitter Runs the Following Product Mix:
1) 5-out Can Stock
2) 10-out Can Stock
3) 12-out Can Stock
4) Brazing Stock
5) Lid Stock
Equipment Specifications:
Cuts:
1) 16 of .030"
2) 30 of .020"
Operational Modes: Tight Line and Single Loop
Hand of Line: Right Hand
Line Speed: 0/2500 FPM, 50 FPM - jog, 50 FPM - Thread

Line Includes:
Unwind Turnstyle
1) Manufacturer: Stamco
2) Type: 4-arm rotating (360 Degree max @ 2 rpm)
3) Hyd Motor: 1 HP
4) Hydro-Motor: 8 in/rev @ 113 rpm = 4 gpm
5) Pump: 8 gpm @ 1000 psi
6) Turnstyle Detente Cylinder: 3.25" bore, 2.5" stroke
7) Pusher Plate Cylinder: Telescoping @ 1.5"/sec
8) Coil Weight: 40,000 pounds ea/arm
9) Coil Width: 44" - 68"
10) Coil O.D. Maximum: 96"
Coil Car (Southworth)
1) Manufacturer: Southworth
2) System Pressure: 1800 psi
3) Rise Time: 56 seconds
4) Tilt Time: 2-3 seconds
5) Traverse Speed: 40 FPM
Unwind Proper And Holddown Roll
1) Unwind
a) Manufacturer: Stamco
b) Drive Motor: 125 HP, 300/1800 RPM
c) Gear Ratio: 2.972:1
d) Blower Motor: 1.5 HP, 1730 RPM
e) Lube Pump Motor: 1.5 HP, 1800 RPM
f) Mandrel: 20.25" expanded, 18.25" collapsed
g) Cylinder: 8" bore, 12" stroke
2) Holddown Roll
a) Manufacturer: Stamco
b) Hydro-Motor: 23.8 in/rev @ 45 rpm = 6 gpm
c) Lift Cylinder: 4" bore, 17" stroke
d) Roll: 8" dia., 18" face, polyurethane cover, 80-90 durometer
3) Edge Guide Unit
a) Manufacturer: MEA
b) Type: 24" positioner with LE105 edge guide laser sensor
c) Pump Drive: 20 HP, 1150 RPM
d) Hyd. Tank Capacity: 150 gallons
e) Pump: 20 gpm @ 1200 psi
f) Cylinder: 8" bore, 12" stroke
g) Gap: 12'
***MEA hydraulics provides pressure to the entry coil car***
Sleeve Storage Table
Coil Peeler Table
Pinch Roll And Drive
1) Manufacturer: Stamco
2) Drive Motor: 20 HP, 850/2300 RPM
3) Lift Cylinders (2 ea): 3.25" bore, 7" stroke
4) Rolls: 1 ea, 8" dia., 72" Face, polyurethane cover, 85-95 duro.
1 ea, 16" dia., 72" face, polyurethane cover, 85-95 duro.
Inspection Section
Thickness Gauge
1) Manufacturer: Accuray (model 7000)
2) Measuring Medium: beta rays
Thread Table & Deflector Pinch Roll
1) Deflector Pinch Roll
a) Manufacturer: Stamco
b) Upper Cylinders (2 ea): 3.25" bore, 7" stroke
c) Lower Cylinder (2 ea): 3.25" bore, 6" stroke
d) Swing Roll (2 ea): 3.25" bore, 5" stroke
e) Hydro-Motor: 23.8 in @ 48 rpm = 6.5 gpm
f) Rolls (2 ea): 8" dia., 72" face, polyurethane cover, 85-95 durometer.
Oiler (Peabody)
1) Manufacturer: Peabody
2) Power Supply Req: 480 v, 30 amp
3) Tank (3 ea): 70 gallons
4) Type Oil: Nalco Xl 174
5) Oil Deposition: 10 - 25 mg/ft
6) Transfer Pumps (2 ea): 6 gpm
Coil Set Machine
1) Manufacturer: Stamco
2) Motor: Hydro-Motor, 11.9 in @ 12 gpm
3) Lift Cylinders (2 ea): 3.25" bore, 4" stroke
4) Work Roll: 2.5" dia., 84.5" face
5) Back-up Roll: 4" dia., 72" face, 2" pitch grooved, right-hand spiral
6) Bridle Rolls (2 ea): 8" dia., 72" face, polyurethane cover, 85-90 duro.
Slitter Proper/Drive/Side Trimmers
1) Manufacturer: Stamco, #6 1/2 x 66" slitter
2) Drive Motor: 125 hp, 300/1800 rpm
3) Gear Ratio: 1.5:1
4) Blower Motor: 1.5 hp, 1730 rpm
5) Side Trimmer Housing Adj. Motor: 1 hp, 1750 rpm
6) Clutch Cylinder: 3.25" bore, 3" stroke
7) Lock Cylinders (4 ea): 2.5" bore, 5" stroke
Scrap Baller
1) Manufacturer: Stamco
2) Drive Motor: 50 hp, 850/2550 rpm
3) Gear Ratio: 4.067:1
4) Eject Hydraulic Cylinder: 4" bore, 15" stroke
5) Traverse Hydraulic Cylinder: 4" bore, 46" stroke
6) Air Cylinder: 8" bore, 21" stroke
7) Air Cylinder: 6" bore, 7" stroke
Pit Thread Table
Synchro-Wind Unit & Drive
1) Manufacturer: Stamco
2) Drive Motor: 150 hp, 300/1500 rpm
3) Gear Ratio: 1:1
4) Blower Motor: 1 hp, 1725 rpm
5) Lift Hydraulic Cylinder (2 ea): 3.25" bore, 25" stroke
6) Air Cylinder: 2.5" bore, 2" stroke
7) Roll (2 ea): 16.5" dia., 72" face, serrated polyurethane cover
Hydraulic Shear
Exit Thread Table
Rewind Proper & Overarm Separator
1) Rewind Proper
a) Manufacturer: Stamco
b) Drive Motors (2 ea): 125 hp, 300/1800 rpm
c) Gear Ratio: #1 - 8.4:1;#2 - 4.2:1
d) Blower Motor: 1.5 hp, 1800 rpm
e) Lube Pump Motor: 1.5 hp, 1800 rpm
f) Mandrel Cylinder: 10" bore, 6" stroke
g) Pusher Plate Cylinder: 4" bore, 107" stroke
h) Mandrels (3 ea): 12"/16"/20"
2) Overarm Seperator
a) Manufacturer: Stamco
b) Air Cylinders (2 ea): 8" bore, 16" stroke
c) Air Cylinder: 4" bore, 22.5" stroke
Exit Coil Car (Removable - Currently Not in Use)
1) Manufacturer: Stamco
2) Dimensions: 69" x 64.5" x 17.75" high
3) Power Drive: 7.5 hp, 460 rpm
4) Pump: 7 gpm
5) Speed: 40 fpm
6) Rise: 24" in 9 seconds
7) Coil Weight Maximum: 40,000 lbs
Rewind Taping Unit
Rewind Turnstile
1) Manufacturer: Stamco
2) Type: 1-arm, rotating (180 Degree max)
3) Hydro-Motor: 24 in @ 2 rpm = 10 gpm
4) Lift: 2"/sec
5) Lock Cylinder: 3.25" bore, 3" stroke
6) Lift Cylinder: 10" bore, 32" stroke
Traversing Downlayer
1) Hydro-Motor: 23.8 in @ 91 rpm = 10 gpm
2) Pivot Cylinders (2 ea): 8" bore, 36" stroke
3) Traverse Cylinder: 5" bore, 106" stroke
4) Traverse Speed: 20 fpm
5) Horn Speed: 20 fpm
6) Pallet Positioner Hydro-Motor: 3 in @ 292 rpm = 4 gpm
7) Pallet Adjust Speed: 1 fpm
Hydraulic System
1) Entry (#2) Hydraulics
a) Tank Capacity: 105 gallons
b) Motor: 15 hp, 1200 rpm
c) Pump: 26 gpm @ 1200 rpm
d) System Pressure: 850 psi
2) Exit (#3) Hydraulics
a) Tank Capacity: 150 gallons
b) Motor: 25 hp, 1200 rpm
c) Pump: 47 gpm @ 1200 rpm
d) System Pressure: 900 psi
Electrical System
1) DC Drive System
a) Manufacturer: Reliance solid state max paks
2) AC Motor Control Center (MCC)
a) Manufacturer: Allen-Bradley
3) Programmable Controller (PC)
a) Manufacturer: Modicon 584L series w/P-190 keyboard
Surface Inspection System
1) Manufacturer: Intec/IBM/Kaiser (CFT)/Integrated Automation
2) Scan Rate: 4800 scans/second
3) Strip Speed Max: 3,000 fpm
Components
1) Interface Panel - defect interpolation/record keeping
2) IBM A.T. Computers - data compilation/sorecard





Get A Price Quote And Answers To Your Questions

To receive a price quote and to get answers to any questions that you have on this equipment fill out this form.